Escape hatch lid December 19, 2022, 04:40:00 pm I need a new escape hatch lid for my 1998 26.5 mid bath. I hesitated a while back in ordering one from Lazy Daze factory. Well since it closed, I don’t know where to look for a new one. I need someone to tell me the exact lid to purchase from another website. I have looked and looked, and have only found ones the approximate sizes. Help? Thank you!
Re: Escape hatch lid Reply #1 – December 19, 2022, 04:56:23 pm Hello,you can email Todd at ldrvtodd@yahoo.com he might have one or direct you in the right direction he used to work at Lazy Daze. Jody 1 Likes
Re: Escape hatch lid Reply #2 – December 19, 2022, 05:28:19 pm Well I would follow this thread99 HatchI ordered the wrong one first and then used the Heng's 90008-C1-LO Escape Hatch LID ONLY fits Current Model 58621-C2 as well on my 1997 TK 2 Likes
Re: Escape hatch lid Reply #3 – December 19, 2022, 07:09:48 pm If you still have your hatch lid in one piece it could be used as a pattern for a sheet metal fabricator to make a replacement from aluminum. I did this for my 2010 LD rear bath and it worked quite well. I first lined the inside with cork shelving insulation. However it attracted mildew so i replaced it with foil bubble insulation that worked quite well until we sold the coach. I also glued rubber door jamb insulation around the inside edges for a seal. 4 Likes
Re: Escape hatch lid Reply #4 – December 20, 2022, 05:05:42 pm Thanks for the screen shot. Where was this ordered from?
Re: Escape hatch lid Reply #5 – December 20, 2022, 05:12:31 pm Quote from: Kamani74 - December 20, 2022, 05:05:42 pmThanks for the screen shot. Where was this ordered from? Mike said it was custom-made, using the old lid as a model.You would need to have a local metal fabrication shop make it.Several LD Caravan members had aluminum lids made years ago, I remember they were fairly expensive.If you can order the correct lid from Todd, it will be the simplest and cheapest way of proceeding.Larry
Re: Escape hatch lid Reply #6 – December 20, 2022, 07:50:50 pm Yes, I found a local metal fabricator to do the work. It took him a couple of tries to get it right. Since then he has moved away.
Re: Escape hatch lid Reply #7 – December 20, 2022, 11:33:47 pm I did a temporary fix on my hatch a couple of years ago with eternabond. I covered the entire hatch for my trip back east until I could order one from the mothership. Needless to say I waited too long to order from LD but I did email Todd to see if he could get me one and he said he’ll look into it, but he never did get back to me. The Eternabond is still holding up though. That stuff is amazing 1 Likes
Re: Escape hatch lid Reply #8 – December 21, 2022, 01:12:07 pm I am not sure whether all escape hatches share a common dimension but I purchased this one to replace my cracked lid and it fit perfectly. It came with a cross bar but you must use all other existing hardware in the replacement. I have had it on for approx. 1 1/2 years and it has remained secure and watertight.Amazon.com: Heng's 90008-C1-LO Escape Hatch LID ONLY fits Current Model...Matt 2 Likes As an Amazon Associate Lazy Daze Owners' Group earns from qualifying purchases.
Re: Escape hatch lid Reply #9 – December 21, 2022, 01:51:29 pm Quote from: Mattb - December 21, 2022, 01:12:07 pmI am not sure whether all escape hatches share a common dimension but I purchased this one to replace my cracked lid and it fit perfectly. It came with a crossbar but you must use all other existing hardware in the replacement. I have had it on for approx. 1 1/2 years and it has remained secure and watertight.Amazon.com: Heng's 90008-C1-LO Escape Hatch LID ONLY fits Current Model...When ordering online, make sure the vendor will accept returns, the escape hatch has come in slightly different sizes through the decadesLarry 1 Likes As an Amazon Associate Lazy Daze Owners' Group earns from qualifying purchases.
Re: Escape hatch lid Reply #10 – December 21, 2022, 02:34:46 pm In the summer of 2019 we decided to change our escape hatch with a escape hatch with a fantastic fan in it. We ordered the new escape hatch from Todd at the mothership. They sent out the correct hatch for our 98~MB. We had looked on line but was not sure if those would fit and did not want to deal with returns. I then cut and added the fantastic fan to the hatch and installed it. If you could reach Todd, that may be the best outcome. The eHatch fan for us has worked Great! Karen~Liam 98 ~ MB NinALog inhttps://www.lazydazeowners.com/MGalleryItem.php?id=4202 1 Likes
Topic: Escape hatch lid (Read 290 times)
previous topic - next topic
Topic: Escape hatch lid (Read 290 times)
previous topic - next topic